SANY Spare Parts
Excavators, cranes, mining machines and concrete equipment
Brand Supply Scope
SANY spare parts for excavators, cranes, concrete pumps and mining equipment used by contractors and mining service fleets across Africa.
Share equipment model, engine model, OEM part number, quantity and destination port. Availability and lead time are confirmed only after compatibility checking.
Common models
- SY215C
- SY365H
- STC250
- STC500
- SRT95C
- HBT8018C-5
Part categories
- Hydraulic parts
- Electrical parts
- Filter and maintenance kits
- Brake parts
Browse SANY Parts by Model
All modelsSANY Quote-Ready Parts
Quotes confirmed after machine model, engine model and part number compatibility checks.
Filter and maintenance kits
SANY Excavator Filter Kit
Maintenance filter kits for SANY excavators used by contractors and mining service fleets. Air, hydraulic and pilot filters follow the machine, but oil, fuel and water separator elements follow the engine — and these four machines carry four different engines: an Isuzu 4JJ1 on the 13.5 t SY135C, a Mitsubishi 4M50 on the 21.9 t SY215C, an Isuzu 6HK1 on the SY365H and a 15.681 L Isuzu 6WG1X on the 49.5 t SY485H. There is no single kit that covers the range. The SY365H alone ships in three builds at 35.0, 36.0 and 38.1 t, so send the full suffix rather than the base model. Send the engine plate with the machine model and we build the kit for that combination instead of shipping a generic set. Tell us the interval you actually run as well: fleets working in abrasive dust change air filters well inside the manual figure, and planning stock around the real interval is cheaper than replacing engines.
Hydraulic parts
SANY Hydraulic Cylinder Seal Kit
Seal kit matching for SANY boom, arm, bucket and outrigger cylinders. Seal kits are identified by the cylinder, not by the machine: bore diameter, rod diameter and the seal groove arrangement decide the kit, and a single excavator carries boom, arm and bucket cylinders in three different sizes, while a truck crane adds outrigger and telescoping cylinders again different. This listing spans a 21.9 t excavator, a 35 to 38.1 t excavator and a 25 t class truck crane, which have nothing in common at cylinder level. Measure the rod diameter and the bore and send those with the machine serial number. Two things worth knowing: a cylinder that has been resealed twice and still leaks usually has a scored rod or a worn gland bore, and no seal kit will fix that; and it is better to buy the kit for the cylinder you are opening than a set for the machine, because a cylinder that is not leaking is best left closed.
Crane and lifting parts
SANY Crane Outrigger Cylinder Parts
Cylinder components and seals for SANY truck crane outrigger systems. Outriggers are a structural safety system and the parts scale with the crane: the STC250 sits at 32.1 to 33.1 t operating weight on a 6.4 by 5.35 m outrigger span with 7 t of counterweight, while the STC500 hybrid builds carry 8.5 to 11 t of counterweight on spans up to 8.0 by 6.42 m. Nothing interchanges across the range, and the suffix matters even within one model — the STC250C5-1 and the STC250C5-8 already differ from each other in outrigger span. Outrigger cylinders carry load-holding valves and those must be replaced like for like: substituting a valve with a different cracking pressure on a load-bearing circuit is not a saving worth making. Send both the chassis nameplate and the superstructure serial number, since crane parts are documented in two separate books.
Crane and lifting parts
SANY Crane Boom Wear Pads and Telescoping Seals
Boom section wear pads, telescopic cylinder seal kits and boom pin bushings for SANY STC-series truck cranes. Wear pads are the part the telescoping duty cycle consumes: the STC250C5-1 extends its full boom in 80 s and retracts in 105 s, the C5-8 build does the same in 70 / 90 s, and every one of those cycles slides the sections over the pads. Pads are identified by boom section and position — top, bottom and side pads on the same section are different parts, and the pad set for section 2 does not fit section 3. Count the sections on your boom and tell us which one is showing metal-to-metal contact, or send a photograph of the wear marks on the section skin. Telescopic cylinder seals are quoted by the cylinder stamping, since the STC250, STC500 and STC800 each carry a different cylinder. If the boom drifts back under load, the problem is more often the holding valve on the cylinder than the seals; we quote the valve separately against the superstructure serial number.
Crane and lifting parts
SANY Crane Winch Brake and Hoist Parts
Main and auxiliary hoist parts for SANY STC-series truck cranes: winch brakes, brake discs and springs, hoist motors, planetary reducers and the counterbalance valve on the hoist circuit. Hoist speed sets the size class of everything on the drum — the STC250 lifts at 125 m/min on the C5-1 and 130 m/min on the C5-8, the STC500 at 135 m/min, and the STC800 is a size class above both, so nothing on the winch crosses between the three. Main and auxiliary hoists on the same crane are separate assemblies with separate part numbers; say which one on the enquiry. If the complaint is a load that creeps down with the control in neutral, the brake and the counterbalance valve account for most cases and cost a fraction of a motor, so we ask for the symptom before quoting the motor. Winch parts are documented in the superstructure book, not the chassis book — send the superstructure serial number, and the cylinder count on the brake if you are ordering brake parts.
Crane and lifting parts
SANY Crane Hoist Wire Rope
Main and auxiliary hoist wire rope for SANY STC-series truck cranes, specified from SANY's own product brochures rather than by tonnage. The export STC250 runs 16 mm rope (16-35W×7-1960) — 175 m on the main winch and 105 m on the auxiliary. The STC500 runs 18 mm (18-35W×7-1960), 220 m and 130 m. The STC800 and the later STC800S both run 20 mm (20-35W×7-1960), 245 m and 145 m. 35W×7 is a rotation-resistant construction and 1960 is the wire tensile grade in MPa: a rope of the same diameter but a different construction can let the hook block spin under load, so diameter alone is not a specification. The letters after the grade on the brochure designation (USS, USZ) code the finish and lay direction and are worth matching to the tag on the old reel. These figures come from export brochures; domestic C5-series builds are not covered by them, so confirm on the machine before ordering. Replace against the discard criteria in the operator manual — broken wires, diameter loss, kinks, birdcaging — not against hours, and check the drum and sheave grooves at the same time: a worn groove shortens the life of a new rope.
Crane and lifting parts
SANY Crane Slewing Bearing and Slew Reducer
Slewing bearing, slew reducer and slew motor parts for SANY STC-series truck cranes. The bearing is sized to load moment, not to the tonnage badge. On SANY's published figures the export STC250 carries 962 kN·m on the base boom, the STC500 1,774 kN·m and the STC800 2,560 kN·m, so raceway diameter, ball size and bolt pattern are a size class apart across the three; the later STC800S is rated at 2,822 to 2,958 kN·m depending on counterweight and is a different build again. The STC250 brochure specifies a single-row ball slewing ring. Maximum slewing speed is 2.0 r/min on the STC500 and STC800 and 2.0 to 2.2 r/min across STC250 brochure editions, while domestic C5 builds of the STC250 list 2.6 to 2.8 r/min — the reducer and motor are matched to that speed. A slewing bearing is a structural safety part and we quote it only against the superstructure serial number. Before ordering one for a crane that slews roughly, measure the tilt clearance with the boom loaded and unloaded and compare it with the wear limit in the manual: jerky starts and stops are more often the slew brake, the slewing buffer valve or the reducer than the bearing.
Concrete pump wear parts
SANY Concrete Pump Wear Plate
Wear plate and cutting ring sourcing for SANY concrete pumps in infrastructure projects. The model code carries the rating: the HBT6013C-5 is the 13 MPa machine at 65 m3/h and 5,790 kg gross, and the HBT8018C-5 is the 18 MPa machine. The second is not a larger version of the first, and the wear parts behind the higher pressure differ. The spectacle wear plate and the cutting ring are a matched pair and are always replaced together — a new ring run against a grooved plate is worn out in a fraction of its life and lets pressure past into the hopper, which is usually what people are trying to fix in the first place. Tell us the plate bore diameter you measure, and whether you want the standard pair or the tungsten carbide faced pair. Carbide costs more up front and is normally the cheaper choice on continuous pours in abrasive aggregate.
Hydraulic parts
SANY Mining Truck Steering Pump
Steering pump support for SANY mining trucks and heavy transport equipment. The SRT95C is a 95 t rigid mining truck at 65 t empty and 160 t fully loaded, powered by a twelve-cylinder 30.5 L Cummins QST30-C1050 with a 60 m3 body. Nothing on a machine of that mass is a light-vehicle part, and the steering pump sits in a circuit with accumulators and an emergency backup supply rather than working as a standalone pump. That matters for diagnosis: steering that is heavy only at idle, heavy throughout, or has lost assist entirely points at three different components, and only one of the three is the pump. Tell us which of those you have. We quote against the machine serial number and the code cast on the pump body, and it helps to say whether you want the bare pump or the pump with its drive coupling, which is a separate item.
Undercarriage parts
SANY Excavator Sprocket and Idler
Sprockets, drive tumblers and front idlers for SANY SY-series excavators. These are sized by machine class, not by model family: the SY135C at 13.5 t, the SY215C at 21.9 t, the SY365H at 35–38.1 t and the SY485H at 49.5 t run four different undercarriage classes, and none of these parts crosses between them. The SY365H alone ships in three builds (-9, -10 and -S) at 35.0, 36.0 and 38.1 t, so send the full suffix rather than the base model. Two things we always ask before quoting: whether you want a bare idler wheel or the complete assembly with recoil spring and track adjuster cylinder, and what condition the track chain is in — a new sprocket run against a stretched chain wears out in a fraction of its normal life, so the two are usually replaced together. The recoil spring is a stored-energy component and should not be stripped in the field.
Undercarriage parts
SANY Excavator Track Chain, Shoes and Rollers
Track link assemblies, track shoes, bottom rollers and carrier rollers for SANY SY-series excavators. Undercarriage wears as one system, so we quote it as one: fitting new chain against a worn sprocket destroys both, and when chain pitch has reached its wear limit the sprocket belongs in the same shutdown. Two details decide the part number and neither is readable from the model name. First, roller count differs between the standard and long-undercarriage builds of the same machine — count the bottom rollers on one side and tell us the number. Second, shoe width is a separate specification from the machine model, since the same SY215C is built with several widths for different ground conditions, and the shoe bolt pattern follows the chain rather than the machine. Abrasive quarry rock and lateritic soils cut undercarriage life well below the manufacturer figures, which is worth planning stock around rather than discovering mid-season.
Send SANY part numbers for a quote
All manufacturer names, brand names, part numbers and logos are used for reference and identification purposes only. This site is not an authorized dealer of the brands mentioned unless explicitly stated.
Request a Parts Quote