SANY SY365H Spare Parts
Quote after compatibility confirmation by machine model, engine model and part number.
Sourcing Parts for SANY SY365H
The pages below cover common wear and maintenance parts for SANY SY365H. Every quote is confirmed against the machine nameplate, engine model and OEM part number to avoid mismatched shipments.
To get a quote, send the SY365H nameplate photo, OEM part numbers, quantity and destination port.
Filter and maintenance kits
SANY Excavator Filter Kit
Maintenance filter kits for SANY excavators used by contractors and mining service fleets. Air, hydraulic and pilot filters follow the machine, but oil, fuel and water separator elements follow the engine — and these four machines carry four different engines: an Isuzu 4JJ1 on the 13.5 t SY135C, a Mitsubishi 4M50 on the 21.9 t SY215C, an Isuzu 6HK1 on the SY365H and a 15.681 L Isuzu 6WG1X on the 49.5 t SY485H. There is no single kit that covers the range. The SY365H alone ships in three builds at 35.0, 36.0 and 38.1 t, so send the full suffix rather than the base model. Send the engine plate with the machine model and we build the kit for that combination instead of shipping a generic set. Tell us the interval you actually run as well: fleets working in abrasive dust change air filters well inside the manual figure, and planning stock around the real interval is cheaper than replacing engines.
Hydraulic parts
SANY Hydraulic Cylinder Seal Kit
Seal kit matching for SANY boom, arm, bucket and outrigger cylinders. Seal kits are identified by the cylinder, not by the machine: bore diameter, rod diameter and the seal groove arrangement decide the kit, and a single excavator carries boom, arm and bucket cylinders in three different sizes, while a truck crane adds outrigger and telescoping cylinders again different. This listing spans a 21.9 t excavator, a 35 to 38.1 t excavator and a 25 t class truck crane, which have nothing in common at cylinder level. Measure the rod diameter and the bore and send those with the machine serial number. Two things worth knowing: a cylinder that has been resealed twice and still leaks usually has a scored rod or a worn gland bore, and no seal kit will fix that; and it is better to buy the kit for the cylinder you are opening than a set for the machine, because a cylinder that is not leaking is best left closed.
Undercarriage parts
SANY Excavator Sprocket and Idler
Sprockets, drive tumblers and front idlers for SANY SY-series excavators. These are sized by machine class, not by model family: the SY135C at 13.5 t, the SY215C at 21.9 t, the SY365H at 35–38.1 t and the SY485H at 49.5 t run four different undercarriage classes, and none of these parts crosses between them. The SY365H alone ships in three builds (-9, -10 and -S) at 35.0, 36.0 and 38.1 t, so send the full suffix rather than the base model. Two things we always ask before quoting: whether you want a bare idler wheel or the complete assembly with recoil spring and track adjuster cylinder, and what condition the track chain is in — a new sprocket run against a stretched chain wears out in a fraction of its normal life, so the two are usually replaced together. The recoil spring is a stored-energy component and should not be stripped in the field.
Undercarriage parts
SANY Excavator Track Chain, Shoes and Rollers
Track link assemblies, track shoes, bottom rollers and carrier rollers for SANY SY-series excavators. Undercarriage wears as one system, so we quote it as one: fitting new chain against a worn sprocket destroys both, and when chain pitch has reached its wear limit the sprocket belongs in the same shutdown. Two details decide the part number and neither is readable from the model name. First, roller count differs between the standard and long-undercarriage builds of the same machine — count the bottom rollers on one side and tell us the number. Second, shoe width is a separate specification from the machine model, since the same SY215C is built with several widths for different ground conditions, and the shoe bolt pattern follows the chain rather than the machine. Abrasive quarry rock and lateritic soils cut undercarriage life well below the manufacturer figures, which is worth planning stock around rather than discovering mid-season.
SANY SY365H Specifications and Selection Notes
| Operating weight | 35,000–38,100 kg depending on variant |
|---|---|
| Rated power | 190.5–212 kW |
| Factory engine | Isuzu 6HK1 / AA-6HK1XQP (6-cylinder, 7.79 L) on the -S and -9 variants |
| Bucket capacity | 1.5–1.9 m³ depending on variant |
| Production status | Currently in production |
How SY365H Differs From the Rest of the Range
- Sold in at least three distinct builds — SY365H-9, SY365H-10 and SY365H-S — at 35.0 t / 36.0 t / 38.1 t with different power ratings. Quote by the full suffix, not just "SY365H".
- The -9 variant uses the Isuzu AA-6HK1XQP, the same engine XCMG fits to the XE370CA — engine parts for these two machines cross brands.
- Roughly 2.7× the weight of the SY135C and using a six-cylinder 7.79 L engine, it shares almost no wear parts with the smaller machines in this range.
Figures compiled from Chinese equipment databases. Manufacturers ship several configurations under one model code, and engine options in particular change the parts that fit — confirm against the machine nameplate and engine plate before ordering.
Commonly Replaced Parts on SANY SY365H
On SANY SY365H excavators working long hours in mining and earthmoving, these part groups are replaced most often. All of them can be quoted with an OEM part number or a nameplate photo.
- Filter kits: air, oil, fuel and hydraulic filters by service interval
- Hydraulic main pump, pilot pump and control valve parts
- Final drive, travel motor and swing motor assemblies
- Boom, arm and bucket cylinder seal kits
- Bucket teeth, adapters, side cutters and pins
- Undercarriage: track chains, rollers, idlers and sprockets
- Engine parts: injectors, turbocharger, water pump and overhaul kits
- Swing bearing and slewing ring parts
This list covers typical wear items for this machine category. Availability for a specific part is always confirmed against the OEM part number.
SY365H Sourcing FAQ
Do you supply spare parts for SANY SY365H?
Yes. Quote-ready SY365H parts currently include SANY Excavator Filter Kit, SANY Hydraulic Cylinder Seal Kit, SANY Excavator Sprocket and Idler and more. Other parts can be confirmed with an OEM part number.
How do I confirm part compatibility for SY365H?
Send the SY365H nameplate photo, engine model and OEM part number. We confirm compatibility before quoting to avoid mismatched shipments.
How are SY365H parts shipped?
Parts ship with export packing by sea or air depending on weight, volume and lead time, with destination port costs confirmed in the quote.
What are the most commonly replaced parts on SANY SY365H?
Frequent replacements on this excavator include filter kits, hydraulic main pump, pilot pump and control valve parts, final drive, travel motor and swing motor assemblies, boom, arm and bucket cylinder seal kits, bucket teeth, adapters, side cutters and pins and more, always confirmed against the OEM part number.