SANY STC500 Spare Parts
Quote after compatibility confirmation by machine model, engine model and part number.
Sourcing Parts for SANY STC500
The pages below cover common wear and maintenance parts for SANY STC500. Every quote is confirmed against the machine nameplate, engine model and OEM part number to avoid mismatched shipments.
To get a quote, send the STC500 nameplate photo, OEM part numbers, quantity and destination port.
Crane and lifting parts
SANY Crane Outrigger Cylinder Parts
Cylinder components and seals for SANY truck crane outrigger systems. Outriggers are a structural safety system and the parts scale with the crane: the STC250 sits at 32.1 to 33.1 t operating weight on a 6.4 by 5.35 m outrigger span with 7 t of counterweight, while the STC500 hybrid builds carry 8.5 to 11 t of counterweight on spans up to 8.0 by 6.42 m. Nothing interchanges across the range, and the suffix matters even within one model — the STC250C5-1 and the STC250C5-8 already differ from each other in outrigger span. Outrigger cylinders carry load-holding valves and those must be replaced like for like: substituting a valve with a different cracking pressure on a load-bearing circuit is not a saving worth making. Send both the chassis nameplate and the superstructure serial number, since crane parts are documented in two separate books.
Crane and lifting parts
SANY Crane Boom Wear Pads and Telescoping Seals
Boom section wear pads, telescopic cylinder seal kits and boom pin bushings for SANY STC-series truck cranes. Wear pads are the part the telescoping duty cycle consumes: the STC250C5-1 extends its full boom in 80 s and retracts in 105 s, the C5-8 build does the same in 70 / 90 s, and every one of those cycles slides the sections over the pads. Pads are identified by boom section and position — top, bottom and side pads on the same section are different parts, and the pad set for section 2 does not fit section 3. Count the sections on your boom and tell us which one is showing metal-to-metal contact, or send a photograph of the wear marks on the section skin. Telescopic cylinder seals are quoted by the cylinder stamping, since the STC250, STC500 and STC800 each carry a different cylinder. If the boom drifts back under load, the problem is more often the holding valve on the cylinder than the seals; we quote the valve separately against the superstructure serial number.
Crane and lifting parts
SANY Crane Winch Brake and Hoist Parts
Main and auxiliary hoist parts for SANY STC-series truck cranes: winch brakes, brake discs and springs, hoist motors, planetary reducers and the counterbalance valve on the hoist circuit. Hoist speed sets the size class of everything on the drum — the STC250 lifts at 125 m/min on the C5-1 and 130 m/min on the C5-8, the STC500 at 135 m/min, and the STC800 is a size class above both, so nothing on the winch crosses between the three. Main and auxiliary hoists on the same crane are separate assemblies with separate part numbers; say which one on the enquiry. If the complaint is a load that creeps down with the control in neutral, the brake and the counterbalance valve account for most cases and cost a fraction of a motor, so we ask for the symptom before quoting the motor. Winch parts are documented in the superstructure book, not the chassis book — send the superstructure serial number, and the cylinder count on the brake if you are ordering brake parts.
Crane and lifting parts
SANY Crane Hoist Wire Rope
Main and auxiliary hoist wire rope for SANY STC-series truck cranes, specified from SANY's own product brochures rather than by tonnage. The export STC250 runs 16 mm rope (16-35W×7-1960) — 175 m on the main winch and 105 m on the auxiliary. The STC500 runs 18 mm (18-35W×7-1960), 220 m and 130 m. The STC800 and the later STC800S both run 20 mm (20-35W×7-1960), 245 m and 145 m. 35W×7 is a rotation-resistant construction and 1960 is the wire tensile grade in MPa: a rope of the same diameter but a different construction can let the hook block spin under load, so diameter alone is not a specification. The letters after the grade on the brochure designation (USS, USZ) code the finish and lay direction and are worth matching to the tag on the old reel. These figures come from export brochures; domestic C5-series builds are not covered by them, so confirm on the machine before ordering. Replace against the discard criteria in the operator manual — broken wires, diameter loss, kinks, birdcaging — not against hours, and check the drum and sheave grooves at the same time: a worn groove shortens the life of a new rope.
Crane and lifting parts
SANY Crane Slewing Bearing and Slew Reducer
Slewing bearing, slew reducer and slew motor parts for SANY STC-series truck cranes. The bearing is sized to load moment, not to the tonnage badge. On SANY's published figures the export STC250 carries 962 kN·m on the base boom, the STC500 1,774 kN·m and the STC800 2,560 kN·m, so raceway diameter, ball size and bolt pattern are a size class apart across the three; the later STC800S is rated at 2,822 to 2,958 kN·m depending on counterweight and is a different build again. The STC250 brochure specifies a single-row ball slewing ring. Maximum slewing speed is 2.0 r/min on the STC500 and STC800 and 2.0 to 2.2 r/min across STC250 brochure editions, while domestic C5 builds of the STC250 list 2.6 to 2.8 r/min — the reducer and motor are matched to that speed. A slewing bearing is a structural safety part and we quote it only against the superstructure serial number. Before ordering one for a crane that slews roughly, measure the tilt clearance with the boom loaded and unloaded and compare it with the wear limit in the manual: jerky starts and stops are more often the slew brake, the slewing buffer valve or the reducer than the bearing.
SANY STC500 Specifications and Selection Notes
| Builds covered | STC500C5-8 and STC500E plug-in hybrid |
|---|---|
| Rated power | 265 kW at 1900 rpm (C5-8) / 243 kW at 2200 rpm (E) |
| Operating weight | 42,500 kg (C5-8) |
| Counterweight | 11 t (C5-8) / 8.5 t (E) |
| Overall dimensions | 14,260 × 2,800 × 3,720 mm (C5-8) |
| Outrigger span | 8.0 × 6.42 m (C5-8) / 7.5 × 6.05 m (E) |
| Main winch line speed | 135 m/min |
| Slewing speed | 2.0 rpm |
| Travel speed / gradeability | 90 km/h (C5-8) / 47 % (C5-8), 45 % (E) |
How STC500 Differs From the Rest of the Range
- This page covers the plug-in hybrid builds. If your machine is a conventional diesel STC500, its weight and power rating will differ — send the nameplate and we work from that instead, since the drivetrain and engine parts are not the same.
- The two hybrid builds differ from each other as well: the C5-8 carries 11 t of counterweight on an 8.0 × 6.42 m outrigger span, the E carries 8.5 t on 7.5 × 6.05 m. Outrigger and counterweight parts do not cross between them.
- Rated lifting capacity is deliberately not listed: no source states it explicitly for this model, and guessing it from the model code would be unsafe for load-bearing part selection.
- Truck crane part numbers are split between the chassis and the superstructure, which are documented separately — send both the chassis nameplate and the superstructure serial number when requesting a quote.
Compiled from a Chinese used-equipment specification database. Figures are indicative and cover the plug-in hybrid builds only; confirm against the machine nameplate before ordering.
Commonly Replaced Parts on SANY STC500
For SANY STC500 truck cranes on lifting and oilfield projects, these are the part groups most often requested. Quotes are confirmed against the crane nameplate and OEM part numbers.
- Outrigger cylinder parts and seal kits
- Winch motor, winch reducer and wire rope parts
- Slewing bearing and slewing reducer parts
- Load moment indicator (LMI) sensors and safety system parts
- Boom telescoping cylinder seals and wear pads
- Hydraulic pumps, balance valves and control valve parts
- Hydraulic hose kits by length, fitting type and pressure rating
- Filter kits and chassis maintenance parts
This list covers typical wear items for this machine category. Availability for a specific part is always confirmed against the OEM part number.
STC500 Sourcing FAQ
Do you supply spare parts for SANY STC500?
Yes. Quote-ready STC500 parts currently include SANY Crane Outrigger Cylinder Parts, SANY Crane Boom Wear Pads and Telescoping Seals, SANY Crane Winch Brake and Hoist Parts and more. Other parts can be confirmed with an OEM part number.
How do I confirm part compatibility for STC500?
Send the STC500 nameplate photo, engine model and OEM part number. We confirm compatibility before quoting to avoid mismatched shipments.
How are STC500 parts shipped?
Parts ship with export packing by sea or air depending on weight, volume and lead time, with destination port costs confirmed in the quote.
What are the most commonly replaced parts on SANY STC500?
Frequent replacements on this truck crane include outrigger cylinder parts and seal kits, winch motor, winch reducer and wire rope parts, slewing bearing and slewing reducer parts, load moment indicator (lmi) sensors and safety system parts, boom telescoping cylinder seals and wear pads and more, always confirmed against the OEM part number.